admin 管理员组文章数量: 1087139
2024年1月17日发(作者：typedef重定义函数的用法)
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int s0
Router(config-if)#ip address 192.168.1.1 255.255.255.0
Router(config-if)#clock rate 6400
Router(config-if)#no shut
%LINK-3-UPDOWN: Interface Serial0, changed state to up
%LINK-3-UPDOWN: Interface Serial0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down
Router(config-if)#int s1
Router(config-if)#ip address 192.168.2.1 255.255.255.0
Router(config-if)#no shut
%LINK-3-UPDOWN: Interface Serial1, changed state to up
Router(config-if)#int lo1
%LINK-3-UPDOWN: Interface Serial1, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to down
Router(config-if)#ip address 1.1.1.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#router ospf 2
Router(config-router)#network 1.1.1.0 0.0.0.255 area 0
Router(config-router)#network 192.168.1.1 0.0.0.0 area 0
Router(config-router)#network 192.168.2.1 0.0.0.0 area 0
%LINK-3-UPDOWN: Interface Serial0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to up
%LINK-3-UPDOWN: Interface Serial1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to up
Router(config-router)#end
Router#ping 192.168.1.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
2
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int s1
Router(config-if)#clock rate 6400
Router(config-if)#ip address 192.168.3.1 255.255.255.0
Router(config-if)#no shut
%LINK-3-UPDOWN: Interface Serial1, changed state to up
%LINK-3-UPDOWN: Interface Serial1, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to down
Router(config-if)#int s0
Router(config-if)#ip address 192.168.1.2 255.255.255.0
Router(config-if)#no shut
%LINK-3-UPDOWN: Interface Serial0, changed state to up
Router(config-if)#int lo1
Router(config-if)#ip address 2.2.2.2 255.255.255.0
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#router ospf 2
Router(config-router)#network 2.2.2.0 0.0.0.255 area 0
Router(config-router)#network 192.168.3.1 0.0.0.0 area 0
Router(config-router)#network 192.168.1.2 0.0.0.0 area 0
%LINK-3-UPDOWN: Interface Serial1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to up
3
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int s0
Router(config-if)#clock rate 6400
Router(config-if)#ip address 192.168.2.2 255.255.255.0
Router(config-if)#no shut
%LINK-3-UPDOWN: Interface Serial0, changed state to up
Router(config-if)#int s1
Router(config-if)#ip address 192.168.3.2 255.255.255.0
Router(config-if)#no shut
%LINK-3-UPDOWN: Interface Serial1, changed state to up
Router(config-if)#int lo1
Router(config-if)#ip address 3.3.3.3 255.255.255.0
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#router ospf 2
Router(config-router)#network 3.3.3.0 0.0.0.255 area 0
Router(config-router)#network 192.168.2.2 0.0.0.0 area 0
Router(config-router)#network 192.168.3.2 0.0.0.0 area 0
Router(config-router)#end
Router#ping 192.168.2.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.2.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
版权声明：本文标题：点到点链路OSPF配置 内容由网友自发贡献，该文观点仅代表作者本人， 转载请联系作者并注明出处：http://roclinux.cn/p/1705474470a486260.html， 本站仅提供信息存储空间服务，不拥有所有权，不承担相关法律责任。如发现本站有涉嫌抄袭侵权/违法违规的内容，一经查实，本站将立刻删除。
发表评论